Puma board (spin 1)
-
- DIP8 - Involved
- Posts: 19
- Joined: Sun Apr 20, 2008 1:48 am
Re: Puma board (spin 1)
hey so is this all closed now? i just saw fred posting this around and ill take 2 to try this out if i can still get in
Re: Puma board (spin 1)
Hi to all
from Mexico
i want 2 pcb
if is possible
best regards

i want 2 pcb

best regards
Re: Puma board (spin 1)
You extras will get one, if you're lucky! :-) I'll add you both to the first post in the wants one section!
Marcos, I edited your post! :-p
If you ask AbeFM nicely, he may relinquish some of his 5, but to be fair, it should be first come, first served.
Fred.
Marcos, I edited your post! :-p
If you ask AbeFM nicely, he may relinquish some of his 5, but to be fair, it should be first come, first served.
Fred.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
Re: Puma board (spin 1)
No worries, I got 5 because I was pretty sure I would *want* 2 plus one spare for monkeying with. So I could give up 2, and perhaps ONE more if people beg and bake me cookies.
Aldo - where in MX? I'm (along with two friends on here) are in San Diego, perhaps you're right across the border?
Fred:
Yes, I'm with you on the heatsink thing. I might play with it a bit - one idea: an extruded or similar L, the devices bolt to it, the board slides/clips/bolts into it, and then that assembled sub-unit could slide into the next sized bigger extruded case.
Well, I really like long leads and sinking them to the roof. I'll pop it open and play with it soon.
Aldo - where in MX? I'm (along with two friends on here) are in San Diego, perhaps you're right across the border?
Fred:
Yes, I'm with you on the heatsink thing. I might play with it a bit - one idea: an extruded or similar L, the devices bolt to it, the board slides/clips/bolts into it, and then that assembled sub-unit could slide into the next sized bigger extruded case.
Well, I really like long leads and sinking them to the roof. I'll pop it open and play with it soon.
-
- DIP8 - Involved
- Posts: 19
- Joined: Sun Apr 20, 2008 1:48 am
Re: Puma board (spin 1)
ok one sounds good
fred im sure you'll contact me for the funds? or will someone else be doing that?

fred im sure you'll contact me for the funds? or will someone else be doing that?
Re: Puma board (spin 1)
Keep an eye on the thread, I'd say.
I want people to prepay Marcos for these after he provides shipping quotes for each of you. Something like this:
Fred.
I want people to prepay Marcos for these after he provides shipping quotes for each of you. Something like this:
- Address to Marcos and I
- Quote to you and I
- Money to Marcos and confirmation of that to me from him
- Board(s) shipped to you
- Confirm receipt of board(s) to Marcos and I
Fred.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
- nitrousnrg
- LQFP144 - On Top Of The Game
- Posts: 468
- Joined: Tue Jun 24, 2008 5:31 pm
Re: Puma board (spin 1)
I agree.Fred wrote:Keep an eye on the thread, I'd say.
I want people to prepay Marcos for these after he provides shipping quotes for each of you. Something like this:
That way there will be no disputes about what did/didn't happen, I'll be in on it all..
- Address to Marcos and I
- Quote to you and I
- Money to Marcos and confirmation of that to me from him
- Board(s) shipped to you
- Confirm receipt of board(s) to Marcos and I
Just gimme some time to organize myself, I'll post here if I have news ;-)
Marcos
Re: Puma board (spin 1)
AbeFM
i live in monterrey , 3 hours of laredo TX
best regards
i live in monterrey , 3 hours of laredo TX
best regards
Re: Puma board (spin 1)
If someone wants a board he can have mine. Since it would never go on a car and may not even be assembled for a while, it might be more useful for someone else.
Jean
Jean
Re: Puma board (spin 1)
I've added a list of those that are or might pull out or give up their boards to the more keen to the first post.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!