| Author |
Message |
|
Bonaparte
DIP8 - Involved
Joined: Fri Jan 05, 2018 10:38 am
Posts: 22
|
|
| Thu Apr 26, 2018 2:36 pm |
|
|
|
Bonaparte
DIP8 - Involved
Joined: Fri Jan 05, 2018 10:38 am
Posts: 22
|
|
| Thu Apr 26, 2018 2:37 pm |
|
|
|
Fred
Moderator
Joined: Tue Jan 15, 2008 2:31 pm
Posts: 15395
Location: Home sweet home!
|
Who welded that? They look pretty nice :-)
Any shots of the whole thing? Which dimension variant is it?
Keep up the good work!
_________________DIYEFI.org - where Open Source means Open Source, and Free means Freedom FreeEMS.org - the open source engine management system FreeEMS dev diary and its comments thread and my turbo truck!n00bs, do NOT PM or email tech questions! Use the forum! The ever growing list of FreeEMS success stories!
|
| Thu Apr 26, 2018 9:01 pm |
|
|
|
Bonaparte
DIP8 - Involved
Joined: Fri Jan 05, 2018 10:38 am
Posts: 22
|
This is 25kg
|
| Thu Apr 26, 2018 10:13 pm |
|
|
|
Bonaparte
DIP8 - Involved
Joined: Fri Jan 05, 2018 10:38 am
Posts: 22
|
|
| Fri May 04, 2018 11:52 pm |
|
|
|
Fred
Moderator
Joined: Tue Jan 15, 2008 2:31 pm
Posts: 15395
Location: Home sweet home!
|
Love the bend test you did! :-) Puts the nay-sayers into silent mode ;-)
_________________DIYEFI.org - where Open Source means Open Source, and Free means Freedom FreeEMS.org - the open source engine management system FreeEMS dev diary and its comments thread and my turbo truck!n00bs, do NOT PM or email tech questions! Use the forum! The ever growing list of FreeEMS success stories!
|
| Sat May 05, 2018 10:09 am |
|
|
|
Bonaparte
DIP8 - Involved
Joined: Fri Jan 05, 2018 10:38 am
Posts: 22
|
|
| Tue Jul 03, 2018 9:12 am |
|
|
|
Bonaparte
DIP8 - Involved
Joined: Fri Jan 05, 2018 10:38 am
Posts: 22
|
|
| Tue Jul 03, 2018 9:16 am |
|
|
|
Fred
Moderator
Joined: Tue Jan 15, 2008 2:31 pm
Posts: 15395
Location: Home sweet home!
|
Subtle detail that I hadn't noticed before: The eye for chain attachment has to be a slot, not a hole, and the remaining pieces of the shank must fit through the appropriate size shackle opening. The slot is to allow the bolt holes in the shackle to pass through and then rotate into position putting the pin through the chain as opposed to the pin through the anchor. Corners should be radiused to allow free movement of the chain/shackle in use. OR the shank must be thin enough to allow the right size shackle to slip over it for the pin to go through. Experimentation with dimensions and strength and movement necessary.
_________________DIYEFI.org - where Open Source means Open Source, and Free means Freedom FreeEMS.org - the open source engine management system FreeEMS dev diary and its comments thread and my turbo truck!n00bs, do NOT PM or email tech questions! Use the forum! The ever growing list of FreeEMS success stories!
|
| Sun Feb 21, 2021 10:28 pm |
|
|
|
Fred
Moderator
Joined: Tue Jan 15, 2008 2:31 pm
Posts: 15395
Location: Home sweet home!
|
So all the links to DXF files etc are gone from the internet, but I happened to have a PDF laying around and I'm working on some DXFs for my personal use. Not sure if I'll FOSS the whole lot or try to capitalise on some of it, but I'm working on this again and should have the first full size prototype done inside the next week as I want to go out and view the America's Cup yacht racing and that starts soon! Attached is Marko's old PDF of his STORM design that is unsearchable on the internet. You can convert to a DXF with this site: https://www.vectorization.org :-D His newer design is called Manork and not available except in photos or by being local to Marko in Slovenia.
Attachments:
File comment: 20kg storm with 80cm scale marker at the bottom, two templates to cut it out per his design.
20KGstorm_IZREZ.pdf [11.14 KiB]
Downloaded 126 times
_________________DIYEFI.org - where Open Source means Open Source, and Free means Freedom FreeEMS.org - the open source engine management system FreeEMS dev diary and its comments thread and my turbo truck!n00bs, do NOT PM or email tech questions! Use the forum! The ever growing list of FreeEMS success stories!
|
| Thu Feb 25, 2021 12:18 am |
|
|
