Frankenso for rusEfi: kits or assembled

If you want to sell that old MegaSquirt or Link hardware, here's the place to try.
Post Reply
User avatar
russian
LQFP112 - Up with the play
Posts: 154
Joined: Fri Feb 01, 2013 4:18 pm
Location: Jersey City, USA

Frankenso for rusEfi: kits or assembled

Post by russian »

bare PCB for rusEfi to be used with an old 64 Mazda ECU case. These four layer boards are larger then the two layer Frankenstein boards, with these one has an option to solder an stm32f4 chip right on the board.

Image

$39
Last edited by russian on Sun Jan 25, 2015 1:50 am, edited 2 times in total.
User avatar
russian
LQFP112 - Up with the play
Posts: 154
Joined: Fri Feb 01, 2013 4:18 pm
Location: Jersey City, USA

Re: Frankenso for rusEfi: kits or assembled

Post by russian »

Also available as a kit with the connector and all the I/O chips

Image

$90

x1 Frankenso board
x12 low-side VNS14NV04
x3 op-amp LMV324IDT
x3 high-side TC4427
x2 2x25 header
x2 SD card socket
x1 VR INTERFACE MAX9926
x1 CAN interface SN65HVD230
x2 33uH Inductor
x2 CAP TANT 220UF
x1 IC REG BUCK 5V 3A
x1 CAP ALUM 680UF
x4 misc diodes for power supply
x1 HIP9011 knock detection chip
x1 4MHz osc for HIP9011
User avatar
russian
LQFP112 - Up with the play
Posts: 154
Joined: Fri Feb 01, 2013 4:18 pm
Location: Jersey City, USA

Re: Frankenso for rusEfi: kits or assembled

Post by russian »

User avatar
Nige
QFP80 - Contributor
Posts: 61
Joined: Sat Aug 10, 2013 5:47 am
Location: New Zealand
Contact:

Re: Frankenso for rusEfi: kits or assembled

Post by Nige »

Interesting... is that the same ECU connector as 90's Mitsubishi/Toyota? Denso OEM ECU case?
IRC nick: ignitionigel or Nige
User avatar
russian
LQFP112 - Up with the play
Posts: 154
Joined: Fri Feb 01, 2013 4:18 pm
Location: Jersey City, USA

Re: Frankenso for rusEfi: kits or assembled

Post by russian »

Yes, same 64 pin connector as 90's Mitsubishi/Toyota/Honda/Mazda. Yep, Denso OEM case from a Mazda 323/Protege/Miata.
User avatar
russian
LQFP112 - Up with the play
Posts: 154
Joined: Fri Feb 01, 2013 4:18 pm
Location: Jersey City, USA

Re: Frankenso for rusEfi: kits or assembled

Post by russian »

Second batch of assembled version 0.4 has arrived. Note larger proto area and two extra low current drivers.
Attachments
IMAG1600%5B1%5D.jpg
User avatar
russian
LQFP112 - Up with the play
Posts: 154
Joined: Fri Feb 01, 2013 4:18 pm
Location: Jersey City, USA

Re: Frankenso for rusEfi: kits or assembled

Post by russian »

New batch of same exact Frankenso 0.4 has arrived - boards are back in stock.

https://www.tindie.com/products/russian ... ll-bundle/
User avatar
russian
LQFP112 - Up with the play
Posts: 154
Joined: Fri Feb 01, 2013 4:18 pm
Location: Jersey City, USA

Re: Frankenso for rusEfi: kits or assembled

Post by russian »

Post Reply