This time I did not order HASL (Hot Air Surface Leveled solder) finish on the boards, instead I went with ENIG (Electroless Nickel Immersion Gold) finish on the boards. I have also ordered a stencil to apply the solder paste to the boards that I place the SMD components on then run through my reflow oven.
Once you determine what option you want, post your decision here and then PM me your shipping information so I can PM you a quote that includes shipping cost to your location and my PayPal information.
Prices have changed due to some design changes and market fluctuation, also the kits will now INCLUDE all the ignitor drivers, the low side drivers, the AAP and MAP sensors this time around.
The capabilities of this board for FreeEMS can be found in the README.md file in my Jaguar repository on github:
https://github.com/DeuceEFI/Jaguar/blob ... /README.md
The change list for the Jaguar PCBs can be found in the TODO.md file in my Jaguar repository on github:
https://github.com/DeuceEFI/Jaguar/blob ... ha/TODO.md
The full schematics and board layout in KiCAD and PDF formats are available in my repository as well.
I generally ship USPS Flat Rate Priority Mail 2-3 day Delivery with Delivery Confirmation to USA addresses ($8.00 without the aluminum case or $10.00 with the aluminum case [the aluminum case requires a bigger shipping box]). For international orders, I ship via the United States Postal Service and I can provide you with low cost (slow) or more expensive (faster) shipping options.
I can provide the aluminum alloy cases with flanged ends for an additional $28.00 USD (plus shipping if ordered separately) or you can order them from:
The San Jose Scientific Shop
You will need to cut out the connector holes in the flanged ends of the case.
If you are thinking about Option #1 or Option #2, you should also consider purchasing one of my USBDMs for $35.00 USD which I can include with your Jaguar 0.7-alpha board to save on shipping costs.
The case and connector are NOT included with any of these kit options.
So here are your ordering options:
Option #1: Bare Jaguar 0.7-alpha board (REQUIRES A BDM TO LOAD THE SERIAL MONITOR PROGRAM!) $15.00 USD
No frills, no components, just the printed circuit board. This option is $15.00 USD plus shipping from USA Zip Code 47433 (ask for a shipping quote if not in the USA). This price remains unchanged from the 0.6-alpha due to a greater volume of boards in the order.
Consider purchasing one of my USBDM boards with this option unless you already have a BDM.
Option #2: Bare Jaguar 0.7-alpha board with full BOM kit (REQUIRES A BDM TO LOAD THE SERIAL MONITOR PROGRAM!) $280.00 USD
The includes a bare PCB with every component in the Bill Of Materials (BOM) in marked bags so you will know the component value and schematic reference ID. This option is $280.00 USD plus shipping from USA Zip Code 47433 (ask for a shipping quote if not in the USA).
Consider purchasing one of my USBDM boards with this option unless you already have a BDM.
Option #3: Jaguar 0.7-alpha with ALL SMD components installed and BOM kit of parts $320.00 USD
This is a Jaguar 0.7-alpha board that will have all the SMD components installed and will include a full BOM kit of parts (in marked bags so you will know the component value and schematic reference ID) for you to solder on the board. Case and connector are NOT included. This option is $320.00 USD plus shipping from USA Zip Code 47433 (ask for a shipping quote if not in the USA).
Option #4: Jaguar 0.7-alpha fully assembled $420.00 USD
This option gives you a fully assembled Jaguar 0.7-alpha board, with a few parts that you will need to install. You will need to install the voltage regulators due to the possibility of them being damaged in shipping if I install them. These are included, but you will need to solder them on (don't worry they have large leads and big pads to solder). This option is $420.00 USD plus shipping from USA Zip Code 47433 (ask for a shipping quote if not in the USA).
If you are ordering Options #2, #3, or #4, they include the TC4424A non-inverting output ignitor drivers and 250kPa MAP sensor. I can provide alternate parts instead of the parts in the above kits for no additional charge if you need them:
- TC4423A inverting output ignitor drivers (most will require TC4424A, ask if unsure)
115kPa or 400kPa MAP sensor (115kPa for N/A engines, 250kPa for N/A or mild boosted engines, 400kPa for wild boosted engines)
For those of you who order Option #1 or Option #2 and you do not already have a Background Debug Module (BDM), I have those for sale as well, they are $35.00 USD (plus shipping if ordered separately), but the BDM is small enough that it can be included in the same shipping carton as Option #1 or Option #2, so there will be no additional shipping charge if purchased with those options. If you would like to purchase a BDM with Option #3, or #4, I can also ship it in the same shipping carton as those kits without any additional shipping cost. My BDM is based on the open source USBDM and additional information can be found at: http://www.coolefi.com/usbdm.php
Note: When using PayPal to send funds, please use the "Send to friend" option and cover the PayPal fees as the prices above do not include the PayPal fee for the transaction.
Note: As of March 10, 2015 I still have 16 Jaguar PCBs available if anyone is interested.