Arttu's MS3 compatible processor board

A home for new designs that are growing but haven't quite got their legs yet!
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Arttu's MS3 compatible processor board

Post by Fred »

Neat! How many did you get made? Do I get a blank souvenir? :-D

For future spins you need to choose a name for it. It's ok to put FreeEMS on it, but not as part of the name. Something like "Designed for FreeEMS" or similar is appropriate. Same goes for ruzki, and everyone else, too.

How about EmmEssFree? A play on MS3 and speech impediments :-)

Fred.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
Arttu
DIP8 - Involved
Posts: 19
Joined: Mon Dec 10, 2012 10:10 am

Re: Arttu's MS3 compatible processor board

Post by Arttu »

Fred wrote:Neat! How many did you get made? Do I get a blank souvenir? :-D
Sure! I got ten boards so there are some spares. I can probably arrange an assembled board for you if think you would have use for it.
For future spins you need to choose a name for it. It's ok to put FreeEMS on it, but not as part of the name. Something like "Designed for FreeEMS" or similar is appropriate. Same goes for ruzki, and everyone else, too.

How about EmmEssFree? A play on MS3 and speech impediments :-)
I know. I just have poor imagination and couldn't come up with any sensible name. Not a bad suggestion, I'll think about it :)
reanimotion
QFP80 - Contributor
Posts: 34
Joined: Sun Apr 14, 2013 8:50 am
Location: Australia

Re: Arttu's MS3 compatible processor board

Post by reanimotion »

Fred wrote:How about EmmEssFree? A play on MS3
+1 ! although I'd drop the double m -> "EmEssFree"
Steve
1981 Porsche 928S Bosch KE3-Jetronic Injection with FrankenCIS http://www.FrankenCIS.com
DonTZ125
QFP80 - Contributor
Posts: 57
Joined: Tue Feb 12, 2013 5:43 am
Location: Scarborough, ON
Contact:

Re: Arttu's MS3 compatible processor board

Post by DonTZ125 »

If you're keeping this MS3 compatible, where's the stepper driver and CAN chip?

Or am I going blind in my old age? :D
Arttu
DIP8 - Involved
Posts: 19
Joined: Mon Dec 10, 2012 10:10 am

Re: Arttu's MS3 compatible processor board

Post by Arttu »

The CAN chip is there, page 3 of the schematic. I dropped off the stepper driver since I haven't seen any plans to support it in the firmware (of course I might be wrong on this).
Arttu
DIP8 - Involved
Posts: 19
Joined: Mon Dec 10, 2012 10:10 am

Re: Arttu's MS3 compatible processor board

Post by Arttu »

Some progress. I assembled the first board. After some struggling I managed to flash the bootloader on it and load benchtest code in. Then I was able to connect it with the EMStudio. Wohoo! I guess the next step is to learn how to make my own build configurations and put together a code version that allows testing with real engine.

Image
Image
Image
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Arttu's MS3 compatible processor board

Post by Fred »

Neat! :-)
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
Crystallattice
TO92 - Vaguely active
Posts: 1
Joined: Mon Nov 24, 2014 9:11 pm

Re: Arttu's MS3 compatible processor board

Post by Crystallattice »

Arttu, do you have the design files available for this daughter card you designed? I only find the pdf versions. I really like what you did and want to do something similar and your design will be a great starting point.
JaniM
QFP80 - Contributor
Posts: 35
Joined: Fri Feb 15, 2013 6:13 am
Location: Finland

Re: Arttu's MS3 compatible processor board

Post by JaniM »

Some test done with this. Works trigger in and gives pulse out from ignition and injectors channels. Outputs is tested only with scope. Next thing to test via Emstudio, when get some time.
Post Reply