Hentai has, very kindly, been sponsored a Jaguar board by Andy: viewtopic.php?f=41&t=1847
This thread will document his hackage and process in making his new shiny hardware work on his Miata!
Take it away, Hentai! :-)
Fred.
Hentai's Project Ditch-MS2
Hentai's Project Ditch-MS2
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
Re: Hentai's Project Ditch-MS2
Awesome! :-)
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
- DeuceEFI
- LQFP144 - On Top Of The Game
- Posts: 578
- Joined: Thu Feb 25, 2010 3:57 am
- Location: Gosport, IN USA
- Contact:
Re: Hentai's Project Ditch-MS2
Sounds like you are on the right path
Andy.
FreeEMS vehicle #11, 1932 Ford 5 Window Coupe with a 1996 GM 3.1L SFI V6 with DIS ignition
FreeEMS vehicle #16, 1996 Chevrolet S10 2.2L SFI I4 with DIS ignition
Owner of http://www.coolefi.com
FreeEMS vehicle #11, 1932 Ford 5 Window Coupe with a 1996 GM 3.1L SFI V6 with DIS ignition
FreeEMS vehicle #16, 1996 Chevrolet S10 2.2L SFI I4 with DIS ignition
Owner of http://www.coolefi.com
Re: Hentai's Project Ditch-MS2
sweet! the path has been set!
Re: Hentai's Project Ditch-MS2
Loving the video build diary! :-)
Make sure you have the output of the reg disconnected from the CPU before testing it.
Make sure you have the output of the reg disconnected from the CPU before testing it.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
Re: Hentai's Project Ditch-MS2
Also, use a 9v or current limit your 12v with a resistor in case of fault.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
Re: Hentai's Project Ditch-MS2
http://youtu.be/vPyuJTlaGBo
testing PSU output
testing PSU output
Re: Hentai's Project Ditch-MS2
http://youtu.be/12oA_4ZQyGo
I tried using EMStudio with no success. Got to get with deuce or fred later.
I take it the board doesn't have firmware on it and thats why emstudio can't read it and gets stopped and fails.
I bet if I knew how I could test better communications.
I tried using EMStudio with no success. Got to get with deuce or fred later.
I take it the board doesn't have firmware on it and thats why emstudio can't read it and gets stopped and fails.
I bet if I knew how I could test better communications.