Page 1 of 3

Wanted Jag board

Posted: Fri May 18, 2012 7:07 pm
by Hentai
I'm after a Jag board and would like to know how much someone would charge me to get one built and ready for testing?
Honestly I don't want to make one and my SMD ablities are non exsitent at this point.

Re: Wanted Jag board

Posted: Sat May 19, 2012 10:36 am
by Dan
Hey Hentai,

I am happy to post you my jag pcb after I have finished A) assembling it and B) testing what I want to test with it.

I will need it for the next month or two max.

Let me know what you think?

Cheers,

Dan

Re: Wanted Jag board

Posted: Tue Aug 28, 2012 3:17 am
by DeuceEFI
Update: Hentai now has his very own Jaguar A3 board to build :-)

Re: Wanted Jag board

Posted: Tue Oct 23, 2012 6:27 pm
by lLuiksl
Where can i get one and how much will it cost?

Re: Wanted Jag board

Posted: Tue Oct 23, 2012 9:01 pm
by DeuceEFI
I don't have any more Jaguar A3 boards left to sell, you could PM Kennybug to see if he has any left.

The changes from A3 to A4 are fairly extensive, so if you can hold off for 1-2 months, I'll finish the design changes and have a batch of A4 boards made.

lLuiksl, what engine are you wanting to run with a Jaguar PCB?

Re: Wanted Jag board

Posted: Wed Oct 24, 2012 8:49 pm
by lLuiksl
Nice to hear from you DeuceEFI
i want to put it on a BMW m10 b18 engine and someday add a turbo but first i need a ecu that i can control 8-) The engine hase been reconditioned.

Re: Wanted Jag board

Posted: Thu Oct 25, 2012 12:53 pm
by lLuiksl
Hi

In last post i forgot to mention that Jes i have 1-2 months and wanted to ask if its possible to soldier the MCU like in this video, i'm pretty good when it comes to soldering (i think:D). I´m to new for this forum and i tried to send a pm but i have to make more replies or something like that but ill get there:)

Re: Wanted Jag board

Posted: Thu Oct 25, 2012 8:36 pm
by Fred
PMs are frowned upon. You should only use them for transmitting private information. Anything project related belongs on the forum in plain sight. I've heavily restricted a number of people for violating this principal, don't be one of them. What's your question? And who were you trying to PM?

Re: Wanted Jag board

Posted: Fri Oct 26, 2012 3:27 am
by DeuceEFI
lLuiksl wrote:Hi

In last post i forgot to mention that Jes i have 1-2 months and wanted to ask if its possible to soldier the MCU like in this video, i'm pretty good when it comes to soldering (i think:D). I´m to new for this forum and i tried to send a pm but i have to make more replies or something like that but ill get there:)
Like Fred stated, PM's are frowned upon unless you are communicating sensitive information (email addresses, PayPal info, etc...)

I hand soldered all the ICs (including the Freescale MCU) on Jaguar A3 Serial #'s 2, 3 and 4; the USB UART/MAX9926/ADUM1201/MOSFETs on the Jaguar A2 Serial #1; and finally the ADUM3201 on the Jaguar A3 Serial #1 (the rest of the IC's on this board were baked on in a homemade reflow oven). I use a Weller WLC100 soldering station with a Weller SPG40 iron with a Weller ST7 0.03" x 0.79mm conical tip.

I use a lead free solder paste from a syringe along with a separate flux paste (also from a syringe) to solder on the ICs using either a reflow oven or a soldering iron.

Re: Wanted Jag board

Posted: Fri Oct 26, 2012 3:30 am
by Fred
You use lead-free? :-o Hmmm.