Decoding Nissan style Mitsi Electric 360 slot cam sensors

For discussing and developing different RPM/Position decoders using our superior modular architecture! One thread per pattern, please.
MotoFab
1N4001 - Signed up
Posts: 307
Joined: Thu May 29, 2008 1:23 am
Location: Long Beach CA

Re: Decoding Nissan style Mitsi Electric 360 slot cam sensors

Post by MotoFab »

The resistor isn't working then?
User avatar
jharvey
1N4001 - Signed up
Posts: 1607
Joined: Tue Jun 10, 2008 5:17 pm

Re: Decoding Nissan style Mitsi Electric 360 slot cam sensors

Post by jharvey »

HOODEY wrote:I am seeing an ignition timing of 65 degrees at idle but I believe it should be
15 degrees.


Anyone care to explain this? I think I have the solution but I am looking for feedback from others.
I think we need more info. This could be cause by RC filters causing physical delay, software latency, math errors, ect. We really need more info to be able to help iron out a detail like that. The calibration technique may be a patch to a different bug, or it may be the required solution, hard to say with out more detail.
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Decoding Nissan style Mitsi Electric 360 slot cam sensors

Post by Fred »

HOODEY, is this an open source solution with a freeems compatible license? If so, publish a code repositiory (preferably git) and if not, the discussion really belongs in another forum section (non-free). If it is FOSS, having the repo would enable others to help you test and diagnose a LOT easier...

Fred.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
HOODEY
DIP8 - Involved
Posts: 17
Joined: Mon Aug 17, 2009 4:03 pm

Re: Decoding Nissan style Mitsi Electric 360 slot cam sensors

Post by HOODEY »

Resistor worked fine.

All had to do with how I understood the Nissan optical wheel. What I thought is TDC is not.
MotoFab
1N4001 - Signed up
Posts: 307
Joined: Thu May 29, 2008 1:23 am
Location: Long Beach CA

Re: Decoding Nissan style Mitsi Electric 360 slot cam sensors

Post by MotoFab »

A series resistor (if that's what was added) shouldn't have worked. There are some other hardware/firmware/peripheral/port issues.

Is this a FOSS design, as Fred was asking?
HOODEY
DIP8 - Involved
Posts: 17
Joined: Mon Aug 17, 2009 4:03 pm

Re: Decoding Nissan style Mitsi Electric 360 slot cam sensors

Post by HOODEY »

Its not free. What is really the purpose of the weak pull up?




Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is performed
by clearing bit RBPU (INTCON2<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on a Power-on Reset.
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Decoding Nissan style Mitsi Electric 360 slot cam sensors

Post by Fred »

If it's not free, you should probably start a thread in the non-free section and stop taking this thread off topic. I can move the related posts over for you if you like.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Decoding Nissan style Mitsi Electric 360 slot cam sensor

Post by Fred »

Fred wrote:If it's not free, you should probably start a thread in the non-free section and stop taking this thread off topic. I can move the related posts over for you if you like.
HOODEY, this thread is NOT for advertisements! You just joined an elite and small group of people who have had their posts removed. If you want to talk about your closed source diy product, put it in non-free. If it's not diy, consider another forum.

Reposting will NOT serve you well.

Fred.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Decoding Nissan style Mitsi Electric 360 slot cam sensor

Post by Fred »

For reference, the new thread: viewtopic.php?f=56&t=1100
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
Locked