View unanswered posts | View active topics It is currently Sun Oct 22, 2017 4:40 pm



Reply to topic  [ 13 posts ]  Go to page 1, 2  Next
KOSH Racing 1995 Mazda MX-5 GRM $2016 Challenge Racer (40th) 
Author Message
LQFP112 - Up with the play
User avatar

Joined: Thu Feb 07, 2008 9:04 pm
Posts: 123
Owner: Steve
Make: Mazda
Model: Mx-5 Miata
Year: 1995
Engine: Mazda BP-4W (from 99 Miata)
Capacity: 1.8L
Power Adders: Possibly NOS, Turbo for 2017
Firmware: 0.2.0-SNAPSHOT-429-gc00110d-GRM2016 FreeEMS-0.2.0-SNAPSHOT-288-gc2a0282-M2CUPCAR-MitsiAndMazda-CAS-4and2.s19
Hardware: Jaguar A7 #42
Description: Engine on Chop Sticks
DIYEFI Build Thread: viewtopic.php?f=67&t=2692

It was a neck-and-neck battle with Fred's 240 GL Sedan, but KOSH* Racing managed to claim the 40th spot with success on the first (very lean) crank Sunday 9/4 around 2pm EST. Both KOSH and Kiwi efforts struggled with various obstacles. KOSH found themselves without any source for metric fuel pump fittings. The bandaid solution was a ⅜" NPT barb wrapped with a half roll of teflon tape for the pickup end, and a modified banjo fitting forced into fuel line on the pressure side. Enough for the start. Barely.

Authentic first start video:
https://www.youtube.com/watch?v=BbmJitqBS4U
Image

First start log screen
Image

What is this car? It's an entry into the Grassroots Motorsports $2016 Challenge - a budget oriented competition ($2016 USD build limit) that's comprised of an autocross (gymkhana), quarter mile drag time and concours. Steve (owner of car and epic beard) purchased the "bumped in rear" Miata for desirable performance parts to install on his personal Miata. After a serious part-out for profit, Steve still had a running, driving car, so it only seemed natural to race it. I was invited to the nonsense and brought along the FreeEMS effort, which only seemed natural to me. Though it's barely more than an "engine on chop sticks" (significantly lighter than the original) there is a vision- rat rod- that vision is second to a sorted car able to compete. For that the fuel system needs completion- including a beer keg gas tank. And then tuning before moving on to the rat rod aesthetics. Some photos because it really happened.

Some kid is asking where his wagon is.
Image

sketchy fuel-pump-in-a-blanket
Image

Super secret high tech IAT isolator for cars that care about heat soaked temp sensors.
Image

Image

Final mounting location- up high under the cowl cover (not installed) and away from the elements.
Image

A7 installed in stock Miata ECU chassis for some PNP action.
Image

And some design art
Image
Image
Image
Image

*King Of Shit Happens

_________________
90 Miata | 302rwhp @ 6450rpm | 281rwftlbs @ 4800rpm | FE-dohc 2.0L turbo


Thu Sep 08, 2016 4:46 pm
Profile
Moderator
User avatar

Joined: Tue Jan 15, 2008 2:31 pm
Posts: 14825
Location: Home sweet home!
Such a privilege to have people like you around, Rob! Thanks for sticking with the best free software and open source engine control solution on the planet. I hope it serves y'all well and the team achieves some solid results in a few weeks. Good luck! :-)

_________________
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!


Fri Sep 09, 2016 6:33 am
Profile WWW
Moderator
User avatar

Joined: Tue Jan 15, 2008 2:31 pm
Posts: 14825
Location: Home sweet home!
/me unchecks "Disable smilies"

:worship:

:novids:

:-)

_________________
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!


Mon Oct 03, 2016 3:28 am
Profile WWW
LQFP112 - Up with the play
User avatar

Joined: Thu Feb 07, 2008 9:04 pm
Posts: 123
KOSH Racing had good weekend in our FreeEMS powered Miata at the GRM Challenge over the weekend. Our effort went exceptionally well considering we started the first morning of the event without lug nuts specific to our competition wheels. And then there's the part where the car had yet to drive itself more than the distance to the trailer for the trip before arriving at the event. Yep- the first time this beast moved itself any measurable length was the first run on the autocross course. Never completed tune, no alignment, no gauges... you get the idea. So a 12th place overall finish is all WIN in my book.

Of course this success came at the price of some late hours and hard work on both sides of the globe. Steve put in loads of late hours in his Tampa shop (Gorilla Garage aka the oven), while on the other side were Kiwis pounding keys and pedals. A group effort is what made it happen.

We managed a top half finish in the autocross and a 14.775 quarter mile time. But the real surprise was the concours score. Fortunately for us the judges favored our ratrod Miata concept and TRUE open source engine management. We made our pitch to the judges and did a good job distinguishing the car from others.

And now for some media to feed the masses.

Named "Tetanus", this Miata was stripped of all body panels except doors, then "rebuilt" with scrap to mimic a flat bad truck complete with a beer keg fuel cell. Total cost on the car by green flag was under $1100 US.
Image

KOSH lined up with an SR20DET powered Opel GT running the stock Nissan ecu. Opel was running low 14s.
Image

That's a carb'd Ford V8 powered Miata on the right running 13s.
Image

KOSH's quick quarter from the event.
Image

KOSH also managed a 3rd place overall in the General Tire Challenge. This was a parallel competition for Challenge competitors on the autocross course. Each driver ran one lap in 2017 Mazda Miata and Mazda3, the combined the times for a final score.
Image

Videos:

14.775 Quarter mile
https://www.youtube.com/watch?v=wx_zgQvpn5A

View of driver/owner Steve making a quarter mile run.
https://www.youtube.com/watch?v=5J1hzAT-K_c

Phone video of the dragstrip:
https://www.youtube.com/watch?v=pSrGJp4tcLE

Phone video from the autocross. Runs not in order- first run in video was low on fuel.
https://www.youtube.com/watch?v=8V930r7j8k8

_________________
90 Miata | 302rwhp @ 6450rpm | 281rwftlbs @ 4800rpm | FE-dohc 2.0L turbo


Wed Oct 05, 2016 10:44 pm
Profile
LQFP112 - Up with the play

Joined: Fri Sep 16, 2011 8:37 pm
Posts: 146
Location: New Zealand
Nice work fellas! Great results. Thanks for sharing the vids.

Love the style and especially that keg, haha.


Thu Oct 06, 2016 8:47 am
Profile
Moderator
User avatar

Joined: Tue Jan 15, 2008 2:31 pm
Posts: 14825
Location: Home sweet home!
I'd just like to point out that it wasn't just me smashing keys and it wasn't just Corbon smashing pedals, we both smashed both, just FYI :-)

PM me for Rob's address if you want to send him a dozen beers :-D

_________________
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!


Thu Oct 06, 2016 11:52 am
Profile WWW
LQFP112 - Up with the play
User avatar

Joined: Thu Feb 07, 2008 9:04 pm
Posts: 123
The car also made a brief appearance in some local TV news coverage. Unfortunately before we had the race rubber on. Apparently we have magically turned that keg into an engine. Amazing what some crafty firmware can do. ;-)

http://www.wcjb.com/local-news/2016/09/ ... ge-compete

Image

_________________
90 Miata | 302rwhp @ 6450rpm | 281rwftlbs @ 4800rpm | FE-dohc 2.0L turbo


Thu Oct 06, 2016 1:18 pm
Profile
Moderator
User avatar

Joined: Tue Jan 15, 2008 2:31 pm
Posts: 14825
Location: Home sweet home!
Not sure if they'd let you run, but those space savers likely should have been your front-axle race rubber on the drag strip.

I might be wrong, but even being steel I'd expect them to have lower inertia than the semi slicks, and certainly lower wind resistance.

Though also far worse braking ability at the end! :-D

Every time I look at the front of that car I can think of only one thing, so here it is for your thread:

Image

_________________
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!


Fri Oct 07, 2016 10:46 am
Profile WWW
LQFP112 - Up with the play
User avatar

Joined: Thu Feb 07, 2008 9:04 pm
Posts: 123
Using them up front crossed my mind, but so did the idea of them being rated at 60mph and the implications of them falling apart at speeds above that on this car. Agree that there are many advantages to them for drag racing. Next year we'll have a better set of drag rubber/wheels.

You're robot reference lacks the distinguishing wagon-esque features. Eyes don't make the beast. :lol2:

_________________
90 Miata | 302rwhp @ 6450rpm | 281rwftlbs @ 4800rpm | FE-dohc 2.0L turbo


Fri Oct 07, 2016 1:25 pm
Profile
Moderator
User avatar

Joined: Tue Jan 15, 2008 2:31 pm
Posts: 14825
Location: Home sweet home!
You can remedy those issues by sourcing some free used motorcycle tyres with an appropriate load raring, however they're not easy to find under seventeen inches.

_________________
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!


Fri Oct 07, 2016 11:27 pm
Profile WWW
Display posts from previous:  Sort by  
Reply to topic   [ 13 posts ]  Go to page 1, 2  Next

Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
Designed by ST Software for PTF. ColorizeIt.