Hentai's 1992 Mazda Miata (15th)

If you're running FreeEMS on any engine whether it be in a vehicle or not, please post about it here!
User avatar
Fred
Moderator
Posts: 15432
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Hentai's 1992 Mazda Miata (15th)

Post by Fred »

Paste:

(11:20:03) Fred: ok, well, if there is a 2v drop across the 1k resistor then you have a 1.5k in the pull down where you should have 100k
(11:20:51) Fred: which could mean they don't turn on reliably
(11:21:11) Fred: so that's the first thing you should check and change
(11:21:25) Fred: and you may want to roll your dwell back at the same time, as they'll fully saturate with 12v applied
(11:22:03) Hentai: if I run my dwell back from 4.8 to 4 I get more noticeable missfires
(11:22:04) Fred: R103 R102 by the looks, make sure these are 100k not 1.5k
(11:22:09) Fred: well yeah...
(11:22:18) Fred: if those numbers are correct,, you're lucky it works at all
(11:22:33) Hentai: haha
(11:23:03) Hentai: so r104 and r105
(11:23:06) Hentai: 100k
(11:23:22) Fred: basically the input of the fet driver is super high impedance and presents almost no load to the cpu at all
(11:23:30) Fred: so seeing 2v across your 1k drive resistors is bad
(11:23:35) Fred: no no
(11:23:41) Fred: 104 and 105 should be 1k
(11:23:42) Fred: check that too
(11:23:43) Hentai: ok
(11:23:49) Fred: they could be 66k if the others are already 100k
(11:23:52) Fred: check all four
(11:24:28) Hentai: I will verify them all on the circuit paths
(11:24:30) Fred: once you have a solid 5v at the input of the driver, you will get a solid nominal 12v at the output assuming a good 12v feed
(11:25:02) Fred: if you still don't have 12v at the inner end of r100 and r101 then the feed is bad
(11:25:07) Fred: or the jumper wrong
(11:25:09) Fred: or no jumper
(11:25:30) Fred: do you have the link in the circle?
(11:25:38) Fred: and is it to the 12v side?
(11:25:50) Hentai: yeah 12v jumped
(11:25:57) Hentai: but I could accuratly check it at the time
(11:25:57) Fred: ok
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
User avatar
DeuceEFI
LQFP144 - On Top Of The Game
Posts: 579
Joined: Thu Feb 25, 2010 3:57 am
Location: Gosport, IN USA
Contact:

Re: Hentai's 1992 Mazda Miata (15th)

Post by DeuceEFI »

More than likely you don't have a 12v supply that is supposed to be connected to the IGN-12v input which supplies 12v to the JP1 and JP2 jumper block. Right now you are probably only feeding the ignitor driver with 5v from the MCU output. This would explain the 2v drop across the 1k resistor and the fact you are only seeing 2.2v to 2.4v on the output pin. There is an internal diode that connects from the gate input to the Vdd input, which would drop the 3v you see at the gate input by approximately 0.707v which would give you about 2.3v on the output pin.

Connect a 12v supply lead to the IGN-12v input near D3 in the LSD3 section of the PCB and then check to see that you have 12v at JP1 or JP2.

Cheers,
User avatar
Hentai
LQFP144 - On Top Of The Game
Posts: 302
Joined: Sun Jul 18, 2010 2:35 pm

Re: Hentai's 1992 Mazda Miata (15th)

Post by Hentai »

DeuceEFI wrote:More than likely you don't have a 12v supply that is supposed to be connected to the IGN-12v input which supplies 12v to the JP1 and JP2 jumper block. Right now you are probably only feeding the ignitor driver with 5v from the MCU output. This would explain the 2v drop across the 1k resistor and the fact you are only seeing 2.2v to 2.4v on the output pin. There is an internal diode that connects from the gate input to the Vdd input, which would drop the 3v you see at the gate input by approximately 0.707v which would give you about 2.3v on the output pin.

Connect a 12v supply lead to the IGN-12v input near D3 in the LSD3 section of the PCB and then check to see that you have 12v at JP1 or JP2.

Cheers,
I have 12v connected to ign-12v. I also read 12v at jp1 and jp2.

I will let the picture do the talking

Image
User avatar
Hentai
LQFP144 - On Top Of The Game
Posts: 302
Joined: Sun Jul 18, 2010 2:35 pm

Re: Hentai's 1992 Mazda Miata (15th)

Post by Hentai »

Image
User avatar
Hentai
LQFP144 - On Top Of The Game
Posts: 302
Joined: Sun Jul 18, 2010 2:35 pm

Re: Hentai's 1992 Mazda Miata (15th)

Post by Hentai »

Perhaps the first actual working Variable vane turbo setups on FreeEMS.
User avatar
Fred
Moderator
Posts: 15432
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Hentai's 1992 Mazda Miata (15th)

Post by Fred »

Hentai wrote:Perhaps the first actual working Variable vane turbo setups on FreeEMS.
Congratulations! :-)
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
User avatar
m2cupcar
LQFP112 - Up with the play
Posts: 139
Joined: Thu Feb 07, 2008 9:04 pm

Re: Hentai's 1992 Mazda Miata (15th)

Post by m2cupcar »

Congrats! very cool
90 Miata | 302rwhp @ 6450rpm | 281rwftlbs @ 4800rpm | FE-dohc 2.0L turbo
User avatar
Hentai
LQFP144 - On Top Of The Game
Posts: 302
Joined: Sun Jul 18, 2010 2:35 pm

Re: Hentai's 1992 Mazda Miata (15th)

Post by Hentai »

Fun

Image
Image
User avatar
Fred
Moderator
Posts: 15432
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Hentai's 1992 Mazda Miata (15th)

Post by Fred »

Ouch! :-(
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
User avatar
Hentai
LQFP144 - On Top Of The Game
Posts: 302
Joined: Sun Jul 18, 2010 2:35 pm

Re: Hentai's 1992 Mazda Miata (15th)

Post by Hentai »

Reinstalled stuff after repairs. If the turbo lets go again I'm going back to N\A for a while

Image
Post Reply