Neat Prototyping Board Design

Non-EMS Electronics related discussions and projects in here please.
Post Reply
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Neat Prototyping Board Design

Post by Fred »

Pretty cool!

http://www.elecfreaks.com/store/flower- ... p-378.html

Image

Someone should design one of these and do a shared run of them :-)

Fred.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Neat Prototyping Board Design

Post by Fred »

Article on development of the above: http://www.elecfreaks.com/2362.html
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
User avatar
Dan
LQFP144 - On Top Of The Game
Posts: 1204
Joined: Tue Mar 02, 2010 2:33 pm
Location: Australia

Re: Neat Prototyping Board Design

Post by Dan »

yep, i would like to do a shared run.

Will be a piece of piss to knock it up in Altium!

Who is keen for one/some/lots ?
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Neat Prototyping Board Design

Post by Fred »

Me. Unsure when, not soon, but early next year I'd love to have some (several) laying around.

Would you just cover the entire surface in them edge to edge? Or? Why?

Which size break? Seeed 100x100 or 200x100 are most cost effective IIRC.

Fred.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
User avatar
Dan
LQFP144 - On Top Of The Game
Posts: 1204
Joined: Tue Mar 02, 2010 2:33 pm
Location: Australia

Re: Neat Prototyping Board Design

Post by Dan »

Probably 200x100 I would think. Rectangular seems to be a good size as opposed to square.

I would do them over the entire surface mostly, with a thin border for neatness.

Probably chuck in some 4mm diameter holes in each corner too :-)
User avatar
Fred
Moderator
Posts: 15431
Joined: Tue Jan 15, 2008 2:31 pm
Location: Home sweet home!
Contact:

Re: Neat Prototyping Board Design

Post by Fred »

Sounds fair! Make it happen. I look forward to seeing high-res photos of them on your desk and cloning the Git repo.
DIYEFI.org - where Open Source means Open Source, and Free means Freedom
FreeEMS.org - the open source engine management system
FreeEMS dev diary and its comments thread and my turbo truck!
n00bs, do NOT PM or email tech questions! Use the forum!
The ever growing list of FreeEMS success stories!
User avatar
Dan
LQFP144 - On Top Of The Game
Posts: 1204
Joined: Tue Mar 02, 2010 2:33 pm
Location: Australia

Re: Neat Prototyping Board Design

Post by Dan »

:-)
Post Reply