DIYEFI.org Forum
http://forum.diyefi.org/

Jaguar 0.7-alpha kits For Sale
http://forum.diyefi.org/viewtopic.php?f=27&t=2457
Page 7 of 7

Author:  reanimotion [ Thu Oct 09, 2014 12:19 pm ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

Arrived today.
Thanks Andy!

Author:  reanimotion [ Sat Jul 11, 2015 6:01 am ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

Serial #33 donated to FreeEMS community

Author:  Fred [ Sat Jul 11, 2015 7:05 am ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

reanimotion wrote:
Serial #33 donated to FreeEMS community

I speak for at least myself and the person in possession of it when I say: Thank you very much! <3

It could run an engine tomorrow, or if not, any day now, and an epic and infamous engine at that! :-D

Author:  AldoQ [ Sat Aug 22, 2015 12:19 am ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

Hi
i want 1 bare pcb and bdm
regrds

Author:  DeuceEFI [ Sun Aug 23, 2015 3:02 am ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

AldoQ wrote:
Hi
i want 1 bare pcb and bdm
regrds


PM sent to AldoQ with cost and shipping information request.

Author:  EFIRick [ Thu Feb 08, 2018 9:14 pm ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

what is the status of new boards/kits?

Author:  DeuceEFI [ Sat Feb 10, 2018 3:42 pm ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

I worked on the design for Jaguar v0.8, which has a few improvements over the v0.7, a while ago. I just haven’t finished the design since I was waiting to see if there were any further refinements to make to the design.

I just recently sold the last of the v0.7 boards so it might be time for a new run of boards. :-)

I do have CoolEFI Basic ECU v0.2-alpha fully assembled boards in stock which is based on the Jaguar schematics and has many of the capabilities of the Jaguar PCB along with a simple Molex connector. I was designed for 4 cylinder engines and has run my 2.2L Chevrolet S10 with FreeEMS using the same firmware that was build for the Jaguar v0.7-alpha that was previously in the S10. The Basic ECU can be found at http://www.coolefi.com.

If there is interest in a Jaguar v0.8 then I will invest some time and money to finish the design and have another run of PCBs manufactured.

Author:  EFIRick [ Sat Feb 10, 2018 7:11 pm ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

If I purchased a FreeEMS board it would need to be V8 compatible, so that leaves off the CoolEFI board.

I also may need a trans controller for this project if I proceed

It would be housed in a OEM case PNP style so I can switch back to OBD2 for emissions compliance testing. 04 Dakota w/Daimler V8

Author:  Matthijs [ Sat Feb 10, 2018 7:23 pm ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

If it helps you to cover some costs I will take one or two pcbs

Author:  EFIRick [ Sat Feb 10, 2018 11:48 pm ]
Post subject:  Re: Jaguar 0.7-alpha kits For Sale

What has changed in the 0.8 board?

Page 7 of 7 All times are UTC [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/