97 LT1 Turbo/MS project
- SleepyKeys
- LQFP144 - On Top Of The Game
- Posts: 549
- Joined: Mon Feb 11, 2008 10:52 pm
- Location: Arizona
- Contact:
Re: 97 LT1 Turbo/MS project
Nope, just flipped one. I used two passenger side manifolds.
You snooze, you lose!
Re: 97 LT1 Turbo/MS project
So, one facing foreward and one facing back? If that is the case I would guess that the drivers is facing foreward and maybe the exhaust from the passenger side comes around the back of the engine and dumps into the other manifold or joins it by a y-pipe very close to the turbine inlet.
I sure would like to get your car on a hoist and just look around!
Thanks for the continuing info by the way.
I sure would like to get your car on a hoist and just look around!
Thanks for the continuing info by the way.
- SleepyKeys
- LQFP144 - On Top Of The Game
- Posts: 549
- Joined: Mon Feb 11, 2008 10:52 pm
- Location: Arizona
- Contact:
Re: 97 LT1 Turbo/MS project
Correct. The car is 200 miles away. When I get it back I'll take some more detailed pics.
You snooze, you lose!
Re: 97 LT1 Turbo/MS project
That would be awesome! I am sure your y-pipe strategy is going to be difficult to get good photos of, but any and all are gladly appreciated.
Re: 97 LT1 Turbo/MS project
I don't suppose you have the specs on the turbo you are using or link a page with the specs?
- SleepyKeys
- LQFP144 - On Top Of The Game
- Posts: 549
- Joined: Mon Feb 11, 2008 10:52 pm
- Location: Arizona
- Contact:
Re: 97 LT1 Turbo/MS project
Its just a T70, p-trim wheel. .70/ar compressor .96/ar turbine. Fred posted the flow map in the thread about my car.
-sean
-sean
You snooze, you lose!
Re: 97 LT1 Turbo/MS project
do you know the actual wheel measurements though?
- SleepyKeys
- LQFP144 - On Top Of The Game
- Posts: 549
- Joined: Mon Feb 11, 2008 10:52 pm
- Location: Arizona
- Contact:
Re: 97 LT1 Turbo/MS project
Turbine Wheel:
-Exducer Diameter: 2.53"
-Mayor Diameter: 2.91"
Compressor Wheel:
-Exducer Diameter: 2.72"
-Mayor Diameter: 3.58"
Turbine Housing:
-A/R: .96
-Type: Undivided
-Discharge: V-Band
-inlet: T4
Compressor housing:
-A/R: .70
-Air Inlet: 4.00"
-Exducer Diameter: 2.53"
-Mayor Diameter: 2.91"
Compressor Wheel:
-Exducer Diameter: 2.72"
-Mayor Diameter: 3.58"
Turbine Housing:
-A/R: .96
-Type: Undivided
-Discharge: V-Band
-inlet: T4
Compressor housing:
-A/R: .70
-Air Inlet: 4.00"
You snooze, you lose!
Re: 97 LT1 Turbo/MS project
Thank you. I want to compare yours to mine...unfortunately I won't be able to measure mine for a few days.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
that could be misinterpreted to sound bad...haha
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
that could be misinterpreted to sound bad...haha
- SleepyKeys
- LQFP144 - On Top Of The Game
- Posts: 549
- Joined: Mon Feb 11, 2008 10:52 pm
- Location: Arizona
- Contact: