| DIYEFI.org Forum http://forum.diyefi.org/ |
|
| DIY Copying New Gen Anchors http://forum.diyefi.org/viewtopic.php?f=13&t=2316 |
Page 3 of 3 |
| Author: | Bonaparte [ Thu Apr 26, 2018 2:36 pm ] |
| Post subject: | Re: DIY Copying New Gen Anchors |
|
|
|
| Author: | Bonaparte [ Thu Apr 26, 2018 2:37 pm ] |
| Post subject: | Re: DIY Copying New Gen Anchors |
  
|
|
| Author: | Fred [ Thu Apr 26, 2018 9:01 pm ] |
| Post subject: | Re: DIY Copying New Gen Anchors |
Who welded that? They look pretty nice :-) Any shots of the whole thing? Which dimension variant is it? Keep up the good work! |
|
| Author: | Bonaparte [ Thu Apr 26, 2018 10:13 pm ] |
| Post subject: | Re: DIY Copying New Gen Anchors |
This is 25kg |
|
| Author: | Bonaparte [ Fri May 04, 2018 11:52 pm ] |
| Post subject: | Re: DIY Copying New Gen Anchors |
http://www.morjeplovec.net/forum/viewto ... &start=300 |
|
| Author: | Fred [ Sat May 05, 2018 10:09 am ] |
| Post subject: | Re: DIY Copying New Gen Anchors |
Love the bend test you did! :-) Puts the nay-sayers into silent mode ;-) |
|
| Author: | Bonaparte [ Tue Jul 03, 2018 9:12 am ] |
| Post subject: | Re: DIY Copying New Gen Anchors |
Test Hall anchor: https://youtu.be/ybxWyEwUPpM Test rocna: https://youtu.be/GqpfUV6Sqlo https://youtu.be/fk3FfhG0TMs https://youtu.be/81GSzD7S1a4 https://youtu.be/oi6FGvPC7ok Test old anchor: https://youtu.be/B4QVnVat6iU https://youtu.be/mSNAbeB-X44 https://youtu.be/3dbH489Of3M Test Danfort anchor: https://youtu.be/nD-3cx9bnHA Test Storm: https://youtu.be/dxkr-4Jox-s https://youtu.be/wHfgWGphOWg https://youtu.be/faoL1WD-QtY https://youtu.be/r5DRxIhyzRA https://youtu.be/NF9DYJi5ONs Test Bruce: https://youtu.be/fw1pHidsFSE https://youtu.be/qALYBgJOGE8 https://youtu.be/8OMuWCMUwns Test BBQ grill  https://youtu.be/GZ2GWtQGSKo https://youtu.be/N8P0X7Zn4IM |
|
| Author: | Bonaparte [ Tue Jul 03, 2018 9:16 am ] |
| Post subject: | Re: DIY Copying New Gen Anchors |
Delta: https://youtu.be/afq0RTuzWkg https://youtu.be/deZ822FQ7sk |
|
| Author: | Fred [ Sun Feb 21, 2021 10:28 pm ] |
| Post subject: | Re: DIY Copying New Gen Anchors |
Subtle detail that I hadn't noticed before: The eye for chain attachment has to be a slot, not a hole, and the remaining pieces of the shank must fit through the appropriate size shackle opening. The slot is to allow the bolt holes in the shackle to pass through and then rotate into position putting the pin through the chain as opposed to the pin through the anchor. Corners should be radiused to allow free movement of the chain/shackle in use. OR the shank must be thin enough to allow the right size shackle to slip over it for the pin to go through. Experimentation with dimensions and strength and movement necessary. |
|
| Author: | Fred [ Thu Feb 25, 2021 12:18 am ] | ||
| Post subject: | Re: DIY Copying New Gen Anchors | ||
So all the links to DXF files etc are gone from the internet, but I happened to have a PDF laying around and I'm working on some DXFs for my personal use. Not sure if I'll FOSS the whole lot or try to capitalise on some of it, but I'm working on this again and should have the first full size prototype done inside the next week as I want to go out and view the America's Cup yacht racing and that starts soon! Attached is Marko's old PDF of his STORM design that is unsearchable on the internet. You can convert to a DXF with this site: https://www.vectorization.org :-D His newer design is called Manork and not available except in photos or by being local to Marko in Slovenia.
|
|||
| Page 3 of 3 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|
