Search found 24 matches
- Thu Mar 15, 2012 9:03 pm
- Forum: FreeEMS General
- Topic: xgate risc instruction set
- Replies: 8
- Views: 16302
Re: xgate risc instruction set
i found it in the s12xgatev2.pdf. just took a lot of searching. time that i really didnt have the time for at the time when i asked. i know it probably seems or sounds stupid that i ask when i can search myself. i usually do search for it. just end up not having enough time to find the answer im loo...
- Thu Mar 15, 2012 8:31 pm
- Forum: FreeEMS General
- Topic: xgate risc instruction set
- Replies: 8
- Views: 16302
Re: xgate risc instruction set
after getting a copy of it some of its instructions arnt so basic. yes it does have a lot of basic instructions. No mul and div instructions thou. but you can still imul and idiv by multiples of 2. i've never seen bit extraction instructions before. @motofab - i saw those but they did not have how t...
- Sun Mar 11, 2012 10:12 pm
- Forum: FreeEMS General
- Topic: xgate risc instruction set
- Replies: 8
- Views: 16302
xgate risc instruction set
i have been looking for the risc instruction set for the xgate to see what capabilities it had. i found a doc that contain some of the instructions and opcodes for it. from reading over the doc i dont believe it is the whole instruction set. has anyone been able to find a complete instruction set. p...
- Thu Mar 08, 2012 7:23 pm
- Forum: FreeEMS General
- Topic: hello
- Replies: 52
- Views: 65415
Re: hello
seems that xgate would be ideal for doing this.
- Thu Mar 08, 2012 4:12 am
- Forum: FreeEMS General
- Topic: hello
- Replies: 52
- Views: 65415
Re: hello
and thanks for the education on pwm.
- Thu Mar 08, 2012 4:11 am
- Forum: FreeEMS General
- Topic: hello
- Replies: 52
- Views: 65415
Re: hello
would it be possible to have a single s12x pass the decoded wheel data to another s12x that would have the sole purpose of just driving the pwm frq for the valve train. or would it be easier to have both see the timing wheel? im asking because on a small engine it might be possible up to 4 cyl to us...
- Thu Mar 08, 2012 12:43 am
- Forum: FreeEMS General
- Topic: hello
- Replies: 52
- Views: 65415
Re: hello
i ment you said, Of course, to do a good job of that you'll likely need a fairly powerful processor, though I can think of a way it could be done well enough with FreeEMS. I'm not certain that I'd recommend it, though. i was wondering if you would specify or pm with what your talking about since you...
- Thu Mar 08, 2012 12:08 am
- Forum: FreeEMS General
- Topic: hello
- Replies: 52
- Views: 65415
Re: hello
ok. what would be your suggestion?
- Wed Mar 07, 2012 11:53 pm
- Forum: FreeEMS General
- Topic: hello
- Replies: 52
- Views: 65415
Re: hello
im not sure i understand how pwm would prevent from hulk smashing a valve into a piston as it begins to fall or comes to tdc. also pwm would create a lot of noise and stress on the valve seats that they were not designed for.
- Wed Mar 07, 2012 11:43 pm
- Forum: FreeEMS General
- Topic: hello
- Replies: 52
- Views: 65415
Re: hello
dont know if i would need a vol dac or an cur dac, but i want to drive special designed solenoids to actuate the valve train and remove the cams and all associated timing components.