Search found 79 matches

by AiToR51
Thu Jan 18, 2018 6:48 pm
Forum: Jaguar
Topic: burn ecu processor
Replies: 6
Views: 26209

Re: burn ecu processor

:lol2:
by AiToR51
Fri Jan 05, 2018 1:20 pm
Forum: Jaguar
Topic: burn ecu processor
Replies: 6
Views: 26209

Re: burn ecu processor

well,near two years later is repaired :lol2: after a few hours of work.

Image

was able to load the s19 using your usbdm and made a fast test of comms with EMStudio, I've to check all inputs and outputs.




although is sad to see this project in this slow growing state.
by AiToR51
Fri Jan 05, 2018 1:13 pm
Forum: Announcements
Topic: Merry Christmas from your trusty leader :-)
Replies: 31
Views: 93946

Re: Merry Christmas from your trusty leader :-)

Merry christmas and happy new year
by AiToR51
Mon May 16, 2016 1:54 pm
Forum: FreeEMS Vehicles
Topic: AiToR51's 1992 Ford Sierra XR4i 2.0 (24th)
Replies: 44
Views: 128893

Re: AiToR51's 1992 Ford Sierra XR4i 2.0 (24th)

I've a log I made today on road, at 80kpa it reached 6100 rpm without any problem. In this engine I don't know with exactitude if Injector flow could be a problem, they are 380cc@3bar. My fuel system is around 3.5 bar without vac, so they should flow a little more, and 0,5bar of boost should be not ...
by AiToR51
Sun May 15, 2016 9:57 pm
Forum: FreeEMS Vehicles
Topic: AiToR51's 1992 Ford Sierra XR4i 2.0 (24th)
Replies: 44
Views: 128893

Re: AiToR51's 1992 Ford Sierra XR4i 2.0 (24th)

I'm having problems above 4000 rpm on boost. Firstly had a lot of syncloss, but solved it partialy cleaning grounds and some connectors. Now it doens't loss sync but it feels like ign cut and in logs you can see wrong rpm http://i.imgur.com/oMTpTAF.png?1 log attached, but with a note, I had some pro...
by AiToR51
Sun May 01, 2016 10:06 am
Forum: FreeEMS Vehicles
Topic: AiToR51's 1992 Ford Sierra XR4i 2.0 (24th)
Replies: 44
Views: 128893

Re: AiToR51's 1992 Ford Sierra XR4i 2.0 (24th)

holset HE351VE http://i.imgur.com/ePy0RDx.jpg http://i.imgur.com/nWwjV3h.jpg engine specs is: 2.0 16v with MLS head gasket forged rods and used forged mahle opel C20XE pistons. Should give me around 8:1 of CR. I would prefered to be on 9:1 but this piston combo is the CR which it gives to me. DIY Ex...
by AiToR51
Tue Mar 01, 2016 11:01 pm
Forum: Suppliers
Topic: Knock Off or "Compatible" Bosch Wideband Sensors
Replies: 2
Views: 22124

Re: Knock Off or "Compatible" Bosch Wideband Sensors

ouch, I had a problem with my LC1 wideband and bought a replacement.. it was cheap.. I will check the resistor prior use.
by AiToR51
Thu Feb 11, 2016 10:04 pm
Forum: Jaguar
Topic: burn ecu processor
Replies: 6
Views: 26209

burn ecu processor

Hi, I was making some tests with my jaguar 0.7 and made a mistake leaving alone a +12v wire that touch the board and the MCU is dead :(:(

where do you recommend me to buy a replacement? same reference or there are more equivalent?
by AiToR51
Fri Dec 18, 2015 10:02 am
Forum: General FOSS EMS
Topic: Holset HE351VE standalone controller (arduino based)
Replies: 3
Views: 21325

Re: Holset HE351VE standalone controller (arduino based)

Yes it was not cheap.. Something around 650 eur with customs fee + shipping from canada


I think also if I've a good working freeems is better to have control on it.. But for first stage i prefer to have it standalone as i've many cars and ecus.
by AiToR51
Thu Dec 17, 2015 10:34 pm
Forum: General FOSS EMS
Topic: Holset HE351VE standalone controller (arduino based)
Replies: 3
Views: 21325

Holset HE351VE standalone controller (arduino based)

I'm starting a new project controlling a Holset HE351VE VGT turbo. I'm building it based on Arduino with the following hardware properties: - CAN BUS communications to control the veins - MAX9926 to read turbo RPM's and engine RPM's (from any magnetic sensor pulley, camshaft sensor, etc..) - two map...